FFT10 interface or RS interface. For. For. EKC EKC For. For .. Danfoss can accept no responsibility for possible errors in catalogues, brochures . Introduction. Features. EKC (for panel mounting) and EKC EKC and are used for. • temperature Danfoss Pt sensors are supplied with . Danfoss EKC – Download as PDF File .pdf), Text File .txt) or read online.
|Genre:||Health and Food|
|Published (Last):||6 April 2018|
|PDF File Size:||1.49 Mb|
|ePub File Size:||2.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Danfoss Place of Origin: Shor tcircuited defrost sensor E5 Def. If a module with data communication is mounted, the controller can send the status of the switch function to the data communication network.
Controller for temperature control – EKC and EKC Manual |
If you want to change the periodical defrost, so that it can be performed at specific times of the day, a clock module may be fitted. When the thermostat calls for refrigeration, the compressor relay will be cut in. Normal operation Known codes and settings Examples of operations See the temperatur at the other controls sensor 1.
If you push the top button in this situation, you will be able to see the alarm message in the display. Temperatures, times, operating conditions, parameter codes and alarm and fault codes Can be read from the display.
Typical questions asked about products Does this product support customization? A-alarms will only become visible when the set time delay has expired.
Danfoss Electronic Controller (EKC EKC ) –
Gold Member Since This danfosss that the gateway with address in the system will have its alarm relay output activated for two minutes. With these settings it will only be possible to set the reference between the two values. Real-time clock With this module you can set up to six individual times for defrost star ts per 24 hours.
The controller will register when the DI input is cut in. The importance is defined with the setting: The digital input can be programmed to – receive alarm signals from an external signal source door alarm – start defrost from an external clock – transmit random alarm signals to the bus system.
The time when water drips off the evaporator. Defrost sensor Here you can set whether a defrost sensor has been mounted. When a PT sensor is used, the danfosz will be shown with one decimal 0. The controller has been specially designed for refrigeration applications, but may of course also be used for other forms of regulation where this is expedient.
This also applies to products already on order provided that such alternations can be made without subsequential changes being necessary in specifications already agreed.
Just push the two buttons simultaneously, and you will be able to change the temperature reference when the display responds by flashing. EKC12 Danfoss The function is fur thermore only relevant if you have chosen defrost with interval star t d The programme will for instance upload all the collected temperature values once a day.
When the compressor is operating, it must run for at least x minutes. Once receive your question, the supplier will answer you as soon as possible. Push both buttons again to conclude the setting Defrost operation Room temp.
If not, you may cancel the ekd by means of setting OFF. Push one of the buttons and select the new value 5. Send your message to this supplier.
Danfoss Electronic Controller (EKC 201 EKC 301)
Danfosss function Fan In addition to the fan functions concerning defrost the fans may also be stopped as a function of the compressor operation and a possible door function. A01 Upper deviation Lower deviation Here you set when the alarm at low temperature is to become activated. Have Own Export License. Manually stop of a defrost operation Defrost operation Reset alarm relay Alarm relay activated Normal operation Room temp.
EKC for panel mounting and EKC for DIN-rail mounting have been specially developed for control duties in refrigeration plant so that operation, ejc and emc are optimised and simplified as much as possible. In controllers with a defrost relay you can set whether the defrost is to be made with electricity or hotgas. It will then star t a defrost cycle.
Three LEDs indicate the actual condition of the system: E Here you can see how controllers are mounted and programmed. Here you set for how long the alarm is to be suppressed.
Controller for temperature control – EKC 201 and EKC 301 Manual
Natural defrost on pump down. Cut-out defrost sensor E4 Def. This cable is dxnfoss connected to a gateway type AKA Push the upper button until a parameter is shown 2. If SPST is cut in, defrost starts. This function is used when too long sensor cables have to be corrected.
Contact Now Click here to send inquiry. Here you set for how long the exact measuring is to be suppressed. The value is set in K. It is also a must that each controller receives power from its own, separate power supply unit.
It is transmitted nowhere.