Read this manual carefully and have your installer instruct you on your system’s operation and on which features have been implemented in your system. I have a DSC model alarm () and this installer code was . The Down and Dirty at unlocking a DSC Alarm with Installers. Parent Directory · PC Pager · PC Partition · PC v Demo User · PC v Installation · PC
|Published (Last):||19 March 2017|
|PDF File Size:||12.56 Mb|
|ePub File Size:||9.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
If I want to lock the door out, I kill power to the whole unit.
How to reset a DSC PC-5010 V2.0, installer code?
When you do this, you are back to square dsc0510. BB code is On. Please login or register. Yes, I had to reset the whole panel as the previous owner left no information. I wanna install a second button in the garage anyway so will need to figure out.
How to reset a DSC PC V, installer code? – Community Forums
Should be an easy interface to the alarm panel. Find all posts by MrRonFL. October 07, I suppose that means the lock switch disables the remote control, otherwise it could simply be in series with the indoor button. If nothing else, I now know how to make my own full-function keypad. My opener has two buttons, one opens the door and the light comes on automatically and the other turns on the light without opening the door. I’ll power down the thing and pull the cluster apart.
I’ve yet to see one dsc5100 in this manner in a residence.
October 08, There must be a circuit breaker that will disconnect power for that ladder job. Since I dont have the “installer code” I can’t get into it and want to know how to reset the system?? Whether I have to actually get licensed after all this I really don’t care. Here’s my intepretation of the manual: You will need the installer manual: If anyone know this please email me or reply.
How to install and programme DSC to open and shut my garage door
LandLine Gold Member Posts: I have all the answers. It does not lock out the wireless keypad mounted on the exterior door frame.
Yep, the outlet for the opener is on its own breaker, which I now turn off if I am up there. What is this old ds5010. It’s a long way down to that concrete when your roof trusses are at 12 feet. It certainly isn’t clear from the installation manual. Short answer, shorting dssc5010 two wires together will raise or lower the graj door -easy. I no longer use the lock function.
But that’s just me. There’s also an LED backlight. The panel will not default if the battery is used. Posted In Plumbing and Piping.
Index of /manuals/DSC/Intrusion Panels/PC5010-Power832
When I found that out, quite by accident, I damn near had a heart attack. Programming suggestions welcome here. I was told I’m lucky that the Installer code of wasn’t locked out.
Installatin 6 – Remove AC power from the control Step 7 – Reconnect all original wiring and power up the control. Logged donnyjaguar Gold Member Posts: I believe 1uF and 50uF. Step 4 – Apply AC power to the main panel.
Hopefully I’ve made this clear enough, I’m sure this has been done a hundred times. Yes, that’s how it works. My installer of course will not give me the “installer code” which I need. My current Genie models have a second button that turns the light on. Step 5 – When Zone Light 1 is lit on the keypad the default is complete.
Trying to hook up tire changer motor to switch. I’m probably over-thinking this being an engineering type. To confuse matters further there are 4 contacts on the opener itself which are shared between the cluster, photocell and beam.
The same breaker might shut the lights off in the garage, also – that would be a challenge. Where I live sdc5010 door openers are required by code to be permanently wired into the electrical service. The logic in the motor control will cycle through down-stop-up with each press.
The output I’m planning on having drive a small relay. Logged I have all the answers. The default procedure is on page Aprilaire – Basic Solenoid Question.